engineering plastics electrical hot wire tester

Brand Name:JINHAIHU

Model Number:ZRS-2

Place of Origin:BEIJING, CHINA

...Hot wire tester Scope of application: The Heating Wire Tester heats the specified material (Ni80/Cr20) and heating wire shape (Φ4mm nickel-chromium wire) to the test temperature (550℃~960℃) for 1 minute, then applies pressure (0.95±0.1 N) for 30 seconds to vertically burn the sample. It is used to determine the ignition risk of electrical...

Brand Name:JINHAIHU

Model Number:ZRS-2

Place of Origin:BEIJING, CHINA

...Hot wire tester Scope of application The heating wire tester heats the specified material (Ni80/Cr20) and the shape of the heating wire (Φ4mm nickel-chromium wire) to the test temperature (550℃~960℃) 1 min, then sets the pressure (0.95±0.1 N)30 s of vertical burning samples. To determine the ignition risk of electrical...

Brand Name:Delta

Model Number:GWT

Place of Origin:China

...overload conditions. Glow wire testing simulates thermal stress caused by glowing elements or overloaded resistors in a short time, to evaluate the risk of fire. The glow wire test applies to electrical and electronic products, household appliance parts,

Brand Name:Rongter

Model Number:WB2-1

Place of Origin:China

RONGTER Customized Top Quality Hand-Pull Type Hot Wire Cutting Machine Fast heating, adequate power to maintain high temperature. Uses: Cuts Polystyrene, Pink Foam, Styrofoam With Ease. Custom Shape and Design Foam for Hundreds of Uses. HOW TO: Heats Up ...

Brand Name:HongCe

Model Number:HWI-1

Place of Origin:China

...Hot Wire Ignition Independent Exhaust Tester With Electrical Control Products Introduction The hot wire ignition tester is designed and manufactured according to the requirements of the "Glow Wire Ignition Test Method" in relevant standards. It is suitable for the ignition risk test of electrical and electronic products and household appliances, and simulates heat sources such as hot...

Brand Name:HAIDA

Model Number:HD-60085

Place of Origin:Guangdong, China (Mainland)

HD-KDRX-II Thermal Conductivity Tester (Hot Wire Method) Description: The hot wire thermal conductivity tester (transient method) is measured using the line source test method of the thermal probe. This thermal probe has a very large aspect ratio to ...

Brand Name:PEGO Group

Model Number:GW-1H

Place of Origin:China

...plastic materials used in electrical devices. Its purpose is to protect against the risk of fire from overheated or electrically energised parts which may cause the plastic material to ignite. This may occur in normal use, under reasonable abnormal use,

Brand Name:LIYI

Model Number:QL-300A

Place of Origin:China

Plastic Raw Material Density Tester Suitable for: Rubber, Plastic, Electric wire, Hard alloy, New materials research lab Principle: Plastic Raw Material Density Tester In accordance with GB/T 533, T1033, ISO 2781, 1183, DIN 53479, ASTM D 297, D792, standards, and by adopting the buoyancy method of Archimedean principle, the machine can accurately and directly show the density of sample. Technical data: A. There are many ways for plastic

Brand Name:D&T

Model Number:DTC-E1212

Place of Origin:CN

Automatic EPS Hot Wire CNC Foam Cutter 380V , Block Cutting Machine styrofoam cutting machine/ eps block cutter/ electric hot wire eps cutter 1. Main Introduction: 1 The cutting process can be showed on the display screen; cutting speed is adjustable (max...

Brand Name:KINGPO

Place of Origin:Mainland China

... of the "Glow Wire Ignition Test Method" in relevant standards. It is suitable for the ignition risk test of electrical and electronic products and household appliances, and simulates heat sources such as hot components or overload resistors. The

Brand Name:HeJin

Model Number:HWI-1

Place of Origin:China

...Hot wire ignition tester With Electrical control Standard: IEC60950-1 Information technology equipment – Safety – Part 1: General requirements Annex A.4 Hot wire ignition test; IEC60947-1 Low-voltage switchgear and controlgear –Part 1: General rules Annex M M.1 Hot wire ignition test (HWI); IEC60695-2-20 Fire hazard testing — Part 2: Glowing/Hot wire based test methods — Section 20: Hot-wire...

Model Number:SN772A

Place of Origin:China

Brand Name:Sinuo

...Wire Tester For EV Charging Connector & Insulating Plastic Flammability Test Product Information This glow wire tester is suitable for testing electrical equipment, automotive on-board electrical components, EV conductive charging connection devices (charging guns, charging sockets, charging modules, internal insulating plastic...

Brand Name:SHUOBODA

Model Number:TCT-2X

Place of Origin:China

...hot-wire method thermal conductivity tester Quickly measure the thermal conductivity of plastics, soil, soft rock, liquids, pastes, granules, powders and other materials using the hot-wire method. Sample shape: block, flake, paste, powder, granule, colloid, or liquid (round, square, or irregular shapes are acceptable, no restrictions on shape), as long as there is a relatively flat sample surface. Description The hot-wire

Brand Name:YUYANG

Model Number:YYF050

Place of Origin:China

...Hot Wire Ignition Test Apparatus Hot wire ignition tester Application: It is suitable for electric and electronic products, household appliance materials to do ignition dangerous test. It simulates the heat source or ignition source of simulates glow component and overload resistance which may cause thermal stress in a short time.Hot-wire...

Brand Name:DAXIAN

Model Number:DX8383

Place of Origin:China

Electrical strength test machine for solid insulating materials Summary: The electrical dielectric strength tester is suitable for testing the breakdown strength and withstand voltage of dielectric, such as plastic, film, resin, mica, ceramic, glass, insulating paint and other media at power frequency voltage. Standards: GB/T5169.10,GB/T5169.13-2006 IEC60695-2-10:Fire hazard testing- Part2-10: Glowing/hot wire testing Machine- Glow-wire...

Brand Name:BAXIT

Model Number:QL–300A

Place of Origin:Shanghai, China(mainland)

...ails: Standard Export Wooden Case Delivery Time: Within 15 Days Plastic Raw Material Density Tester Suitable for: Rubber, Plastic, Electric wire, Hard alloy, New materials research lab Principle: Plastic Raw Material Density Tester In accordance with GB/T

Brand Name:MG

Model Number:MG-HT-2

Place of Origin:Guangdong China

Plastic Electric Kettle CE/ ROHS/ LFGB Approved Pure White Kettle Specifications Capacity 1.7Liter Power 220-240V 50Hz 1850-2200W Heating Plate SUS202 Plug VDE Plug with copper wire cable Controllor Chinese Tianming controller Indicator Blue Light ...

Brand Name:Infinity Machine

Model Number:RS-8000

Place of Origin:Made in China

...Wire Tester Universal Test Machine for Lab Model: RS-8000 Application: This UTM are suitable for the testing of tensile, compression, shearing force, adhesion, peeling force, tear strength, fatigue etc for semi-product & finished product in the field of rubber, plastic, metal, nylon, non-woven fabrics, testile, tape, electric wire...

Place of Origin:China

Brand Name:CHENGFENG

Hot Wire Testing Machine test the Stability of Electronic and Electrical Products During Operation Specification item value Customized support OEM, ODM, OBM, Software reengineering Place of Origin China Guangdong Warranty 1 Year Brand Name CHENGFENG Model ...