HOOYA PJ-611D

Categories	Sleeve Connector
Brand Name:	PJ-611D
Stock:	3000
Voltage Rating (Max):	50V
Model Number:	PJ-611D
Operating Temperature:	-20℃~+70℃
Delivery Time:	5-6周
Packaging Details:	Through Hole
Description:	6.35mm Headphone Jack 1A 50V Through Hole
Connector Type:	6.35mm Headphone Jack
Current Rating:	1A
MOQ:	300

Contact Now

Add to Cart

Company Info.

Shenzhen ECER Network Technology Co., Ltd.

Verified Supplier

Haven't found right suppliers
Our buyer assistants can help you find the most suitable, 100% reliable suppliers from China.
And this service is free of charge.
we have buyer assistants who speak English, French, Spanish......and we are ready to help you anytime!

Submit Buying Request

Product Name: 6.35 PHONE JACK (DIP)

Series: 7355

Model: HY-WI-32

Manufacturer: HAOYU (HONG KONG) LIMITED

Date: 2008-07-23

HAOYU

HONG KONG

Z5/Riss

Item	Test Conditions	Specifications
1. RATING		DC50V 1A
2. OPERATING TEMPERATURE RANGE	PRESERVATIVE TEMPERATURE RANGE	-20C~70C \| 15C~35C

Item	Test Conditions	Specifications
3. ELECTRICAL PERFORMANCE	CONTACT RESISTANCE (Measured by the contact resistance apparatus or meter at 0.1A DC5V. The result is the average of 5 successive measurements.)	70m max
3. ELECTRICAL PERFORMANCE	INSULATION RESISTANCE (Between terminals, Between individual terminals and frame)	100M min
	DIELECTRIC STRENGTH (Between terminals, Between individual terminals and frame)	AC 250V 1 MIN. WITHOUT DAMAGE TO PARTS, ARCING OR BREAKDOWN ETC.

Item	Test Conditions	Specifications
4. MECHANICAL PERFORMANCE	INSERTION AND WITHDRAW FORCE	3-40N
4. MECHANICAL PERFORMANCE	STRENGTH (A static load of 10 N (1000gf) shall be applied to the tip of the terminals for 60 sec. in any direction of actuator.)	WITHOUT DAMAGE OR EXCESSIVE LOOSENESS OF TERMINALS

Item	Test Conditions	Specifications
5. DURABILITY	Wave-soldering	Within 3 seconds at 260 5C
	Hand welding	Within 3 seconds at 380C or below
	LIFE TEST (An actuator shall be subjected to 5000 cycles at a speed of 30 cycles/min)	CONTACT RESISTANCE 200m; MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
	HEAT TEST (852C for 48 hours, then keep in normal condition for 30 minutes)	APPEARANCE, MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
	HUMIDITY TEST (402C 90-96%RH for 48 hours, test after keeping in normal condition for 30 min)	APPEARANCE, MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
	COLD TEST (At -402C for 48 hrs, after test keep in normal condition for 30 min)	APPEARANCE, MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED.
	SALT SPRAY TEST (5% NaCl liquor for 24 hours, after washing, keep in normal condition for 30 min)	WITHOUT EXCESSIVE CORROSION OR CRACK IN APPEARANCE

ROSIN AND OTHER INSULATING AND CAUSTIC MATERIAL CAN NOT BE DIPPED INTO THE ROCKET DURING SOLDERING.
PRODUCTS CAN NOT BE BLOWN WITH AIR GUN OR CLEANED WITH A SOLVENT AFTER SOLDERING.
ALL PARTS OF THE PRODUCTS CAN NOT BE DISSOLVED BEFORE SOLDERING.
AVOID STORING THE PRODUCTS IN A PLACE AT HIGH TEMPERATURE, HIGH HUMIDITY AND IN CORROSIVE GASES.
SHELF LIFE IS LESS THAN 180 DAYS SINCE THE GOODS WERE SENT OUT FROM OUR FACTORY. OUR COMPANY DOESN'T ACCEPT RESPONSIBILITY FOR REJECTS IF THE SHELF LIFE OF GOODS EXCEEDS 180 DAYS.
PLEASE FEEL FREE TO REPORT TO US IF YOU DISCOVER THE INFERIOR GOODS, SO THAT WE CAN TAKE NOTE, CHECK, TRACK AND IMPROVE THEM. THANKS.

Send your message to this supplier


*From:	Your email address is incorrect!
*To:	Shenzhen ECER Network Technology Co., Ltd.
*Subject:	Subject is empty!
*Message:	For the best results, we recommend including the following details: -Self introduction -Required specifications -Inquire about price/MOQ Characters Remaining: (0/3000) Please enter 20 to 3000 characters to contact this supplier!